Cisco CCNA

Some people ask me how to pass Cisco CCNA Exam and get Cisco CCNA certification. I guarantee that you see my answer about Cisco CCNA exam ,you will get your Cisco CCNA certification.

I guarantee your success in the first attempt. If you do not pass the CCNA 640-802 (Interconnecting Cisco Networking Devices Part 1) on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.

Practice Exams for 640-802 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

Printable Exams (in PDF format) Our Exam 640-822 Preparation Material provides you everything you will need to take your CCNA exam. The CCNA Certification details are researched and produced by Professional Certification Experts who are constantly using industry experience to produce precise, and logical. You may get CCNA exam questions from different web sites or books, but logic is the key. Our Product will help you not only pass in the first CCNA exam try, but also save your valuable time .

Comprehensive questions with complete details about 640-802 exam. 640-802 exam questions accompanied by exhibits. Verified Answers Researched by Industry Experts and almost 100% correct. Drag and Drop questions as experienced in the Real CCNA exam. 640-802 exam questions updated on embedded system. Like actual CCNA Certification exams, 640-802 exam preparation is in multiple-choice questions (MCQs). I have tested by many real CCNA exams before publishing.
.

This is a part of Cisco CCNA questions and answer, If you need all Cisco CCNA   640  TestPassport， please  contact me。

1. Refer to the exhibit. What could be possible causes for the “Serial0/0 is down” interface status?
(Choose two.)
A. A Layer 1 problem exists.
B. The bandwidth is set too low.
C. A protocol mismatch exists.
D. An incorrect cable is being used.
E. There is an incorrect IP address on the Serial 0/0 interface.
Answer: AD
2. The network administrator has discovered that the power supply has failed on a switch in the company
LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series
switch. What must be done to ensure that this new switch becomes the root bridge on the network?
A. Lower the bridge priority number.
B. Change the MAC address of the switch.
C. Increase the VTP revision number for the domain.
D. Lower the root path cost on the switch ports.
E. Assign the switch an IP address with the lowest value.
Answer: A
3. Refer to the exhibit. Assume that all of the router interfaces are operational and configured correctly.
How will router R2 be affected by the configuration of R1 that is shown in the exhibit?
A. Router R2 will not form a neighbor relationship with R1.
B. Router R2 will obtain a full routing table, including a default route, from R1.
C. R2 will obtain OSPF updates from R1, but will not obtain a default route from R1.
D. R2 will not have a route for the directly connected serial network, but all other directly connected
networks will be present, as well as the two Ethernet networks connected to R1.
Answer: A
4. Before installing a new, upgraded version of the IOS, what should be checked on the router, and which
command should be used to gather this information? (Choose two.)
A. the amount of available ROM
B. the amount of available flash and RAM memory
C. the version of the bootstrap software present on the router
D. show version
E. show processes
F. show running-confi
Answer: BD
5. Which three IP addresses can be assigned to hosts if the subnet mask is /27 and subnet zero is usable?
(Choose three.)
A. 10.15.32.17
B. 17.15.66.128
C. 66.55.128.1
D. 135.1.64.34
E. 129.33.192.192
F. 192.168.5.63
Answer: ACD
6. A network administrator is explaining VTP configuration to a new technician. What should the network
administrator tell the new technician about VTP configuration? (Choose three.)
A. A switch in the VTP client mode cannot update its local VLAN database.
B. A trunk link must be configured between the switches to forward VTP updates.
C. A switch in the VTP server mode can update a switch in the VTP transparent mode.
D. A switch in the VTP transparent mode will forward updates that it receives to other switches.
E. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP
revision number.
F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the
configured VTP domain membership.
Answer: ABD

The Cisco CCNA  Answer Update